300W IP67 waterproof constant voltage 0/1-10V PWM dimmable led driver
Input Voltage: 100-277VAC
Power Range:80-300W
High Efficiency: up to 86% ; PF>0.95
IP67 Design; Flicker-free
PWM Output Design
Loading: 10%-100% Dimming: 0-100%
Cooling by free air convection
Suitable for dry, damp, or wet location use
Compatible with 0/1-10VDimmers
Protection:short circuit/over loading /over current/ Over temperature
7 years warranty
Model No. | Power | Output Voltage | Output Current | Weight(kg) | Size(L*W*Hmm) | Packing |
OTM-PD80-12-F | 80W | 12V 24V | 6.67A | 1.1 | 230*70*43 | 290*270*160mm/30pcs /CTN |
OTM-PD96-24-F | 96W | 12V 24V | 4A | 1.1 | 230*70*43 | 290*270*160mm/30pcs /CTN |
OTM-PD100-12-F | 100w | 12V 24V | 8.33A | 1.1 | 230*70*43 | 330*270*160mm/30pcs /CTN |
OTM-PD120-12-F | 120w | 12V 24V | 10A | 1.1 | 230*70*4 | 360*270*175mm/30pcs /CTN |
OTM-PD150-12-F | 150W | 12V 24V | 12.5A 6.25A | 1.5 | 256*78*47 | 360*270*175mm/30pcs /CTN |
OTM-PD200-12-F | 200W | 12V 24V | 16.67A | 1.5 | 256*78*47 | 395*255*170mm,30pcs /CTN |
OTM-PD300-12-F OTM-PD300-24-F | 300W | 12V 24V | 25A 12.5A | 1.7 | 276*78*48 | 390*310*185mm,10pcs /CTN |
Specifications
Protection | Short Circuit | shut down o/p voltage, re-power on to recover after fault condition removed |
Over Loading | 30W: ≤120% shut down o/p voltage, re-power on to recover after fault condition removed 60W/300W: ≤120% Hiccup mode,recovers automatically after fault condition is removed 80W-120W: ≤120% constant current limiting, auto-recovery | |
Over temperature | 100℃±10℃ shut down o/p voltage, automatically recover after cooling | |
Environment | Working TEMP. | 40~+60℃ |
Working Humidity | 20 - 95%RH,non-condensing | |
Storage TEMP. Humidity | -40~+80℃,10~95%RH | |
TEMP .cofficient | ±0.03%/℃(0~50℃) | |
Vibration | 30W-60W: 10~500Hz, 2G 10min./1 cycle,period for 60min. each along X,Y,Z axes 80W-300W: 10~500Hz, 5G 10min./1 cycle,period for 60min. each along X,Y,Z axes | |
Safety& EMC | Safety standards | UL8750 +UL1310,CAN/CSA-C22.2 No.250.13 EN61347-1 EN61347-2-13 |
Withstand voltage | I/P-O/P:1.88KVac | |
Isolation resistance | I/P-O/P:100MΩ/500VDC/25℃/70%R | |
EMC EMISSION | FCC 47 CFR Part 15 Subpart B, EN55015,EN61000-3-2,3 (≧60%loading | |
Notes | 1. All parameters NOT specially mentioned are measured at 120VAC input , rated load and 25℃ of ambient temperature. 2. Tolerance: includes set up tolerance, line regulation and load regulation . 3. The power supply is considered as a component that will be operated in combination with final Equipment. Since EMC performance will be affected by the complete installation, the final equipment manufactures must be-qualify EMC Directive on the complete installation again. |
Package
Dimensions
Driver Connecting Diagram
Dimming Operation
※ Built-in 3in 1 dimming function,Output luminous can be adjusted through output cable connecting a resistance or 0/1-10Vdc or 10V PWM signal between DIM+ and DIM-
※ Please DO NOT connect "DIM-"to " LED-"
Warning
※1)This driver should be installed by qualified and professional person;
※2)Please make sure the driver is installed with adequate ventilation around it to allow for heat dissipation.
※3)Ensure that wiring is correct before test in order to avoid light and power supply damage;
※4)f driver Cannot work normally, don’t maintain privately; Have any question, please contact us.